|
~~ Guarantee and Warranty Memorandum ~~
Guarantee
JET-HOT Coatings carry a Life Time Guarantee against rust-through of new headers when coated inside and out. If rust-through, that is a rust hole completely through the substrate metal develops, your headers will be repaired and recoated at no charge.
If the customer is not satisfied with the colour or finish of the coating we will refund the purchase price of the coating only. This is subject to the parts being returned to
JET-HOT for the coating to be removed. This must be carried out within 30 days of purchase.
JET-HOT Coatings applied to new or used
headers, or other components, are conditionally guaranteed for three (3) years. During this period,
headers or other components may be returned for unsatisfactory workmanship defects like missed spots, or coating defects like cracks, to be recoated at no charge. Extreme exhaust temperatures exceeding 704Deg C will be recoated once (1) at no charge during the first 12 months on only Vehicles used in normal driving conditions and not
competitive racing.
Conditions
JET-HOT Guarantee will not apply if there is obvious physical abuse of the coating, modification, welding of the
components or when used for competitive racing of Motor Vehicles such as cars, motorcycles and boats, but not limited to these descriptions.
Life Time Guarantee will not apply to any components that are only partially coated for any reason as requested by the customer, or by the limited access of the design of the
components, (eg. mufflers.) or Internal engine component. These types of
components are only Guaranteed at the point of consumer sale against workmanship and coating defects only.
JET-HOT will not cover the cost of Installation or removal of
components or any damage that may result of the installation or removal.
The JET-HOT Guarantee is not transferable buy the end Consumer. That is a Consumer who has commissioned a trader to have the headers coated or a Consumer who has dealt directly with
JET-HOT.
All Guarantee and Warranty periods start from the date of purchase. If some part is re-coated or replaces the Guarantee and Warranty period applies as of the original purchase date.
Regulations
This Warranty/Guarantee is additional to any consumer right applicable under Statute or Common Law.
Product List
JET-HOT Guarantee only applies to JET-HOT Hi-Lustre,
JET-HOT satin Black, JET-HOT satin Blue, JET-HOT satin Cast iron grey,
JET-HOT satin Red, JET-HOT satin Orange and
JET-HOT Thermal Dissipation Coating. JET-HOT Hi-Temp Black and
JET-HOT 2000 are only covered at the point of consumer sale against workmanship and coating defects.
Transport Disclaimer
All shipping and/or transport charges will be the responsibility of the customer. Any damage or loss of
components during shipping is the responsibility of the company or persons who have possession of the
components at the time the damage or loss occurs. Any Transport Insurance is the customers responsibility.
Warranty Disclaimer for parts or components used in any form of motor sport.
Due to the nature of performance applications, all
JET-HOT Products are sold without any expressed warranty or any implied warranty.
JET-HOT shall not under any circumstances, be liable for any special, incidental or consequential damages, including, but not limited to, damages or loss of property or equipment, loss of profit or revenue, cost of purchased or replacement goods, or claims of customers of purchaser which may arise and/or result from the sale, installation or use of these
products.
JET-HOT reserves the right to make product improvements/changes without notice and without incurring liability with respect to similar
products previously produced.
Product Specifications
Like all products there are limitations, JET-HOT
Hi-Lustre, Black, Cast Iron Grey and Blue coating have a maximum temperature of 1300f (704C) and a minimum of -375f (-190C).
JET-HOT 2000 has a maximum temperature of 2000f (1094c) and
JET-HOT Hi-Temp Black has a maximum of 1800f (843c). JET-HOT Orange and Red have a maximum of 630f (345c). Because there are many things controlling internal engine temperature
JET-HOT can not be held responsible for any damage to the coating resulting from over heating. The maximum temperature specified is sufficient to allow the normal use of motor vehicle operation. In
performance applications these limits are often exceeded for the gain of more power.
Regulation Disclaimer
If the use of this coating on some parts does not comply with Federal and or State government regulations then
JET-HOT Coating Australia Pty Ltd. cannot be in any way held responsible. It is suggested that Federal and or State government Regulations be checked.
This Guarantee and Warranty differ from the JET-HOT
DIRECT Warranty. Information on the JET-HOT
DIRECT is available in the JET-HOT DIRECT Warranty Memorandum.
Internal Engine Coating
The following procedures must be carried out before any parts can be refitted into an engine. When preparing the engine parts for coating they is subjected to different processes that fill them with grit and it is very important to clean them thoroughly before assembly.
Remove all oil gallery plugs to clean the gallery thoroughly and make sure any spit holes are clear. Clean engine parts with Solvent and NOT CAUSTIC based liquids, as these will remove the coating and also damage alloy parts.
The valve seat and valve faces may have been coated and this must be removed for the valve to work successfully.
Pistons must be thoroughly cleaned with a solvent like turpentine (nothing stronger) allowed to drying thoroughly, and then oiling the skirts prior to assembling into the engine. Always be sure you clean the bore thoroughly, use the white rag test.
Any areas of a part that may have coating on it (eg. Bearing or Seal surfaces) can be removed by careful rubbing with 400-grit emery tape, thoroughly clean part after.
These warnings are provided to the customer with every job.
Product Specifications
JET-HOT TBC (Thermal Barrier Coating) Maximum temperature of 705C - cure temperature 343C for half hour.
JET-HOT LFC (Low Friction Coating) Maximum Temperature 810C – Cure Temperature 150c for one hour.
Internal Engine Coating
Disclaimer:
Piston manufactures use all kinds of metal and other elements in combinations of metals alloys in the production of pistons. When the coating is applied, the pistons are subjected to re-heating. This re-heating may alter the structure of the metal. When
JET-HOT receive pistons we are unable to identify the alloys that may be more susceptible to this phenomenon. The coating application system used to apply the coating demands the piston be re-heated over the critical temperature that this phenomenon may occur. Therefore
JET-HOT make no claim that a set of pistons will not suffer from this phenomenon and fore warn all customers.
Piston coating is a risky business JET-HOT take all care and caution when applying the coating
endeavouring not to cause any changes in the piston.
When a customer has agreed to coat pistons they have entered into an agreement with
JET-HOT knowing that there is a risk involved in coating pistons and that neither party has assigned any claims or obligations. Internal Engine Component are Guaranteed at the point of consumer sale against workmanship and coating defects only.
Appendix
Descriptions
The words JET-HOT and JET-HOT Australia refers to JET-HOT Coatings Australia Pty. Ltd.
Competitive racing of Motor Vehicles, competitive racing and performance
applications, shall refer to cars, motor cycles and boats, but not limited to these descriptions, used in competitive racing in off road track or even on highway sanctioned racing events, but not limited to these racing/competition descriptions.
Products shall refer to any Coating applied by
JET-HOT Coatings Australia Pty. Ltd. and not the parts they are applied to.
Component and or Headers shall refer to Parts coated in
JET-HOT coating.
Explanation of terms
The term Life time Guarantee refers to when the customer gets any parts coated as described above, they are guaranteed for the expected life span of the parts, or a minimum of 10 years.
The term "If you don't like, you don't pay" features in some USA origin promotion literature and can also be described as a money back guarantee,
"if you don't like", that is the look or finish of the Coated parts then,
"you don't pay", that is, we will refund the full cost of the coating only subject to the conditions outlined above. JET-HOT Australia has dropped this term for legal reasons.
The above terms are featured prominently in our older Brochures that where supplied to us from JET-HOT USA.
|